How do I turn off my discovery 2 Immobiliser?

How do I turn off my discovery 2 Immobiliser?

Immediately open the door, insert the key in the ignition switch and turn the switch to position II. If the ignition switch is not turned to position II within 30 seconds of the end of the 5 minute wait, the engine is automatically immobilised again.

Can you bypass an Immobiliser?

You can bypass the immobilizer by placing the key in keyhole hence deactivating the car’s immobilizer to remote start. The added security with Mobokey allows the security to be activated as soon as the phone moves away from the car, so you don’t have to worry about car security.

How do you get the EKA code on Discovery 2?

The EKA code is found on the security information card supplied with your vehicle. The code is 4 digits long. The EKA code IS NOT the code in the key fob. The grey plastic tag on the keys IS NOT the EKA code, it is the ignition key code.

How do you reset the Immobiliser on a Land Rover Defender?

Go to the vehicle and press unlock or lock multiple times repetitively until the indicators flash and red dash light flashes very fast for around 10 seconds. That means it’s synced and and you should be good to go.

How do I reset my Land Rover Defender Immobiliser?

How do I disarm my Immobiliser?

Turn the key to unlock your car door, but don’t release it. Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder.

How do I disable Immobiliser?

Step 3: Use Your Car Door Key Hold the key in place for around 30 seconds to let the immobilizer unit know that you have the right key. You can try turning the key on both sides, lock, and unlock. The action will aid you in bypassing the system and deactivate the immobilizer if it recognizes the key.

What is a Nanocom?

Custom Remap for the TDV6 – EMS Flash File [NANOCOM] A custom VBF Remap file that can be programmed into the engine management using our diagnostic server based systems applicable to Discovery 3 / LR3 or Pre 2010 Range Rover Sport with a TDV6 Diesel Engine.

How do I reset my Immobiliser?

To reset the immobilizer, hold down the panic button. Wait for ten minutes if you push the lock button two times.

Where is the immobiliser problem Disco 2 Td5 auto’02?

Immobiliser Problem Disco 2 TD5 Auto ’02. – Discovery Forum – LR4x4 – The Land Rover Forum Immobiliser Problem Disco 2 TD5 Auto ’02. Immobiliser Problem Disco 2 TD5 Auto ’02. Location:Foot of the Ben. Fort William on the west coast of Scotland. I’ve read through everything I can find on this and I’m still a bit confused as to the cause/solution.

Is the D2 immobiliser bypassable?

any immobiliser is bypassable. it might not be easy , might require new parts and some wiring and you might be there for a while, but its not impossible. inpraccticle yes but not impossible. far far simpler to fix what is wrong with it though and get it working as it should. The D2 immobiliser is not bypassable easily or quickly.

Is there a way to bypass the immobiliser?

The D2 immobiliser is not bypassable easily or quickly. this is why car thiefs will break into your house and steal your keys, rather than attempt a more traditional type of TWOC. The immobiliser on mine has been switched off and switched back on again. Click to expand…

How to start immobiliser with new fuse box?

So, new fusebox in passenger comp fitted, new RF receiver fitted and headlining replaced. Turned key to pos’ 2 and left it for five mins then turned it on. After a bit of flashing lights, (including one I’d not seen before, the 0 shape with a diagonal line through it) the immobiliser turned off and she started!