How thick is Hardie Reveal Panel?

How thick is Hardie Reveal Panel?

5/16 in.
HardiePanel vertical siding is 5/16 in. thick and is available in 4×8, 4×9 and 4×10 sizes. Please see your local James Hardie dealer for texture and size availability. HardiePanel vertical siding is available as a prefinished James Hardie® product with ColorPlus® Technology.

How thick is Hardie siding?

1/4 in.
Staggered Edge Panel

Thickness 1/4 in.
Length 48 in. (4 ft.)
Height 15.25 in.
Exposure 6 in.

How thick is James Hardie board and batten?

HardieTrim® Batten Boards are 19mm (¾ in) thick, 64mm (2½ in) wide, and come on 3,658mm (12 ft) lengths. See your local dealer for details and availability of product colors and accessories. A Complete James Hardie Exterior – Close-up on trim products.

What is Hardie Reveal Panel System?

Reveal Panel System is a noncombustible fiber-cement panel siding, manufactured by James Hardie Building Products Inc. Product Dimensions. Product Composition. Reveal panels used in the Reveal Panel System are a Grade II, Type A, fiber-cement flat sheet as defined by ASTM C 1186.

How thick is fiber cement siding?

Sizes. Masonry-finish fiber cement comes in panels that are 5/6 or 5/8 inch thick and in varying sizes from 18 inches by 6 feet to 4 by 12 feet.

How heavy is a Hardie panel?

Hardieplank weighs 2.3 lbs per square foot. That is about the same weight as 5/8″ thick Sheetrock. Hardieplank is installed on load-bearing walls.

What does Hardie board weigh?

How thick should battens be?

A true batten is 2-inches in width or smaller, but you can use larger widths by installing trim in place of a batten if you want a thicker appearance. They’re installed directly over the vertical panels to get the traditional look.

What is a panel reveal?

Flannery’s Wood Panel Reveal is a trim for millwork panels that creates an aesthetic reveal between two millwork panels. The Wood Panel Reveal comes with a 3/8” face flange, which allows the installer to slide the wood paneling in behind the flange and cover the unfinished edge of the panel.

What is siding reveal?

Sometimes referred to as the reveal, siding exposure is the visible space between the bottoms of adjacent rows of siding. Exposure differs from the total height of your siding planks because rows of siding will slightly overlap each other during installation.

How can you tell if siding is fiber cement?

The key to tell if you have fiber cement siding is to check for a wood-grain pressing. Older models of asbestos siding used a similar approach to make the siding look natural—which makes sense, because fiber cement siding was made to replace asbestos.

How thick are Allura panels?

Horizontal Siding: Allura Lap Siding. 1. Thickness: 5/16 inch (7.9 mm), plus or minus .

What is James Hardie Reveal panel?

Beginning with a commercial grade panel developed for multi-family and light commercial applications, the Reveal Panel system by James Hardie is a complete solution for creating a panelized look. Eliminate the guesswork in creating this look with the Reveal Panel system, with all parts including panels, trims and fasteners supplied by James Hardie.

What are the dimensions of a Reveal panel?

Thickness – 7/16 inch Length – 95½ inches Width – 47½ inches All national, state, and local building code requirements must be followed and where they are more stringent than the Reveal® Panel System installation requirements, state and local requirements will take precedence. Document Scope This document applies to the Reveal® Panel System.

Why James Hardie siding?

James Hardie products offer flexible design solutions and high performance in any climate, protecting what matters most to homeowners. Showcased on the exterior of the Nest Connected Home are the Reveal Panel System and Artisan V-Rustic siding.

How do I contact James Hardie for product support?

When in doubt about assembly details, contact the architect, specifier, or a building official. Contact your James Hardie Sales and Install Representative for product support 1-800-9HARDIE (1-800-942-7343). Preparation Ensure the drainage plane is intact and all penetrations are sealed.