What does E1 and F9 mean on a Whirlpool washer?

What does E1 and F9 mean on a Whirlpool washer?

A Whirlpool washer E1 or F9 error code (FP with some models) means that the washer is taking too long to drain (typically, over 8 minutes). If it is not the drain hose or detergent, your washer most likely has a clogged filter, defective drain pump or pressure switch, or loose wiring.

What does E09 mean on a Whirlpool washer?

It means the overflow contacts on the water level pressure switch have been closed for more than 60 seconds. When this error occurs the central control unit will turn the drain pump on indefinitely as a safety precaution to keep the washer from flooding your home.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I fix E01 on my washing machine?

How to Diagnose and Fix Fault Code E01

  1. Switch off and unplug your machine.
  2. Check the door lock itself. (Sometimes the plug on the lock can melt.)
  3. Check the wiring to the door lock.
  4. Check the wiring to the control board from the door look.

How do you clear the code on a whirlpool F9?

Reset the appliance

  1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
  2. Monitor the range or oven for one (1) minute to ensure the error code does not display again.
  3. Verify the range or oven operation.

How do I fix E1 error on my Whirlpool washer?

Possible Solutions

  1. Check that the water faucets are not closed.
  2. Check that the water pressure in the house is over 20 kPa.
  3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
  4. Check that the drain hose is not below 27½” (700 mm) from the floor.

What does F09 mean on washer?

LONG DRAIN TIME
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

What does LF on my washer mean?

too long to fill
If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. Either the F8E1 or the LF error codes may indicate there is some problem with the water supply going to the washer. Please make sure both inlet hoses are connected and both hot and cold water supplies are turned on.

What does lf mean on a Whirlpool Cabrio?

Long Fill
Cabrio Washer Fault Codes

Fault Code Washer Problem
LF (F30) Long Fill
Ld (F32) Long Drain
uL (none) Unbalanced load
oL (F70) Overloaded

What does E01 mean on a washing machine?

E01 – there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 – the machine has failed to fill with water during its allocated time.

What does Whirlpool duet washer error code E01 F09 mean?

Whirlpool Duet Washer Error Code E01 F09 – How To Fix – How To Clear? Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME.

Why does my Whirlpool washer keep going into Drain Mode?

When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water. This means there is a possible fault in the Drain pump, Pressure Switch, or the Electronic Control Board – CCU.

How do you unlock the door on a whirlpool washing machine?

To get the door to unlock you have to take the back of washer off. You will then take the pump filter off, (turns by hand). Drain water out. Put it all back together, plug it in, wait a minute, then door will unlock. I found out how to fix it!